Pump body is Dura-Glas fiberglass reinforced thermoplastic -- lightweight, rustproof, and exceptionally strong. All components in contact with water are resistant to the corrosive and abrasive forces found in the most aggressive water conditions.
Multi-port, reinforced polypropylene precision diffuser design primes faster and handles more air
Precision-molded Noryl® impeller gives perfect balance and ultra-smoothness for highest performance and efficiency
Performance-proven, simple, built-in pressure regulator is adjustable for best performance on all deep well installations. Pressure gauge included, as well.
Stainless steel heat sink provides maximum cooling of the mechanical shaft seal
Dustproof canopy on motor completely encloses electrical components and provides dust, dirt and insect protection. Ventilating air cannot contaminate vital switching components.
Pump can be disassembled without disturbing the piping for easy serviceability. "Control room" motor design makes all motor components easily accessible for service.
PUMP BODY CONSTRUCTION: Dura-Glas (Fiberglass Reinforced Thermoplastic)
HORSEPOWER: Available in 1/2, 3/4, 1, and 1-1/2 HP
MAXIMUM CAPACITY: 26.3 GPM (model MPLF in Shallow Well Setup)
FLOW at 10' LIFT and 40 PSI: 13.8 GPM (model MPLD in Shallow Well Setup)
MAX LIFT: 120' (model MPLF in Deep Well Setup)
MAX SHUT-OFF PRESSURE: 72 PSI (model MPLC)
MAXIMUM TOTAL PRESSURE (Inlet + Pump Pressure): MPLC: 72 PSI / MPLD: 62 PSI / MPLE: 62 PSI / MPLF: 64 PSI
PRESSURE SWITCH SETTING: 30 - 50 PSI
SUCTION SIZE: 1-1/4" NPT
DRIVE SIZE: 1" NPT (suction - over - drive)
DISCHARGE SIZE: 1" NPT
AMP DRAW (full load): (Model & Voltage Dependent)
VOLTAGE: 230 / 115 AC, 60 Hz
RECOMMENDED BREAKER: (HP and Voltage Dependent)
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
IMPELLER: Noryl (R)
NOZZLE: Noryl (R)
VENTURI: Noryl (R)
CLAMP: Stainless Steel
SHAFT: Stainless Steel
DIFFUSER: Reinforced polypropylene with brass wear ring
: . . . Noryl® is a registered trademark of SABIC Innovative Plastics IP BV
Convertible Deep Well Jet Pumps, 1/2 HP, Cast Iron
HR Series Jet Pumps provide reliable service for many residential homes and farms, as well as commercial and industrial applications.
The 4WHR series solids handling pumps are designed primarily for commercial applications such as schools and churches, industrial plants, shopping centers, apartments and condominiums, marinas, interstate rest stops, sewage collection systems, campgrounds, motels, restaurants, office and commercial buildings, state and federal parks, hospitals and nursing homes, dewatering, trailer parks and treatment plants. This pump can be installed with a quick-disconnect slide rail system. Its ability to handle 3-inch spherical solids makes it ideal for most light to medium commercial installations.
Myers® powerful high head 5 HP self-priming pump delivers strong dependable performance for the most demanding jobs. The heavy duty 84JM motor, brass impeller, and large capacity rugged cast iron pump end deliver reliable and continuous high performance service.
The SRA-125 Rail System is tailored to your specific hydraulic needs for low pressurized sewer system requirements.
Package includes your choice of a 2 HP submersible grinder pump, SRA rail system, control panel, three floats and a polyethylene basin available at various depths.
Liftout rail system provides ease of installation and removal for the centrifugal grinder pumps. The SRA System uses a cast iron discharge elbow with integrated ball check valve. Also available with spark-proof rails for hazardous locations. Available with Polyethylene or Fiberglass basin.